2022 Isuzu F Series 2022 Isuzu F Series FRR 110-240 Manual Beavertail

** In Stock Ready for Delivery **

- 5mm chequer plate flooring
• L/H/S of tray 4800mm of tray floor starting after headboard to have built in cabinets. 1000mm high x 1200mm wide x 600mm deep x 4 off. 1st 2 cabinets have fixed shelf in centre of cabinet. 3rd cabinet to have centre shelf then 2 shelves 1 above and 1 below in centre of that space. 4 cabinet has pigeon holes about 200mm x 200mm full box of them. 4 x Gas Strut assisted lids fitted.
• Witches hat spike fitted to floor behind cabinets
• Recessed section behind Witches hat spike to suit storage for Wacker just in-front of the beaver section of tray
• R/H/S behind headboard is 500mm for signs to be stored then a heavy-duty frame for customer supplied compressor to sit on 740mm long x 1400mm deep x 400mm high with fold down door fitted to outside edge
• R/H/S after compressor to be 100mm x 100mm RHS post uprights fitted to store tools into. This is to be raised above deck for cleaning purposes. 5 off post uprights
• 2 x Pipe reals fitted behind 1 off supplied and 1 of to be copied
• Recessed steps fitted behind reels just before beaver to access tray floor. Hand rail and hinged door fitted
• 1 x Mesh chock box fitted to each side of body under tray 1000mm long x 450mm deep x 500mm high Approximately, top 250mm is to be open for putting things into. 50 x 50 mesh cages painted black
• 2 x 1600mm long tubes fitted under rear of chassis where possible with rear end capped off and flat type cap with latch fitted to be able to lock. Accessible from L/H/S
• Fold down boot cleaner fitted on L/H/S under cabinet (brush type)
• 240volt inverter fitted in L/H/S front cabinet to run power lead off
• Slimline flashing beacon fitted to centre of headboard with switch fitted to dash with warning light
• Ladder holders fitted on inside edge of cabinets as per customer requirements
• 2 x swivel type work light fitted at headboard where possible wired to switch on dash with warning light
** In Stock Ready for Delivery **

** In Stock Ready for Delivery **

- 5mm chequer plate flooring
• L/H/S of tray 4800mm of tray floor starting after headboard to have built in cabinets. 1000mm high x 1200mm wide x 600mm deep x 4 off. 1st 2 cabinets have fixed shelf in centre of cabinet. 3rd cabinet to have centre shelf then 2 shelves 1 above and 1 below in centre of that space. 4 cabinet has pigeon holes about 200mm x 200mm full box of them. 4 x Gas Strut assisted lids fitted.
• Witches hat spike fitted to floor behind cabinets
• Recessed section behind Witches hat spike to suit storage for Wacker just in-front of the beaver section of tray
• R/H/S behind headboard is 500mm for signs to be stored then a heavy-duty frame for customer supplied compressor to sit on 740mm long x 1400mm deep x 400mm high with fold down door fitted to outside edge
• R/H/S after compressor to be 100mm x 100mm RHS post uprights fitted to store tools into. This is to be raised above deck for cleaning purposes. 5 off post uprights
• 2 x Pipe reals fitted behind 1 off supplied and 1 of to be copied
• Recessed steps fitted behind reels just before beaver to access tray floor. Hand rail and hinged door fitted
• 1 x Mesh chock box fitted to each side of body under tray 1000mm long x 450mm deep x 500mm high Approximately, top 250mm is to be open for putting things into. 50 x 50 mesh cages painted black
• 2 x 1600mm long tubes fitted under rear of chassis where possible with rear end capped off and flat type cap with latch fitted to be able to lock. Accessible from L/H/S
• Fold down boot cleaner fitted on L/H/S under cabinet (brush type)
• 240volt inverter fitted in L/H/S front cabinet to run power lead off
• Slimline flashing beacon fitted to centre of headboard with switch fitted to dash with warning light
• Ladder holders fitted on inside edge of cabinets as per customer requirements
• 2 x swivel type work light fitted at headboard where possible wired to switch on dash with warning light

** In Stock Ready for Delivery **

- 5mm chequer plate flooring
• L/H/S of tray 4800mm of tray floor starting after headboard to have built in cabinets. 1000mm high x 1200mm wide x 600mm deep x 4 off. 1st 2 cabinets have fixed shelf in centre of cabinet. 3rd cabinet to have centre shelf then 2 shelves 1 above and 1 below in centre of that space. 4 cabinet has pigeon holes about 200mm x 200mm full box of them. 4 x Gas Strut assisted lids fitted.
• Witches hat spike fitted to floor behind cabinets
• Recessed section behind Witches hat spike to suit storage for Wacker just in-front of the beaver section of tray
• R/H/S behind headboard is 500mm for signs to be stored then a heavy-duty frame for customer supplied compressor to sit on 740mm long x 1400mm deep x 400mm high with fold down door fitted to outside edge
• R/H/S after compressor to be 100mm x 100mm RHS post uprights fitted to store tools into. This is to be raised above deck for cleaning purposes. 5 off post uprights
• 2 x Pipe reals fitted behind 1 off supplied and 1 of to be copied
• Recessed steps fitted behind reels just before beaver to access tray floor. Hand rail and hinged door fitted
• 1 x Mesh chock box fitted to each side of body under tray 1000mm long x 450mm deep x 500mm high Approximately, top 250mm is to be open for putting things into. 50 x 50 mesh cages painted black
• 2 x 1600mm long tubes fitted under rear of chassis where possible with rear end capped off and flat type cap with latch fitted to be able to lock. Accessible from L/H/S
• Fold down boot cleaner fitted on L/H/S under cabinet (brush type)
• 240volt inverter fitted in L/H/S front cabinet to run power lead off
• Slimline flashing beacon fitted to centre of headboard with switch fitted to dash with warning light
• Ladder holders fitted on inside edge of cabinets as per customer requirements
• 2 x swivel type work light fitted at headboard where possible wired to switch on dash with warning light
** In Stock Ready for Delivery **

** In Stock Ready for Delivery **

- 5mm chequer plate flooring
• L/H/S of tray 4800mm of tray floor starting after headboard to have built in cabinets. 1000mm high x 1200mm wide x 600mm deep x 4 off. 1st 2 cabinets have fixed shelf in centre of cabinet. 3rd cabinet to have centre shelf then 2 shelves 1 above and 1 below in centre of that space. 4 cabinet has pigeon holes about 200mm x 200mm full box of them. 4 x Gas Strut assisted lids fitted.
• Witches hat spike fitted to floor behind cabinets
• Recessed section behind Witches hat spike to suit storage for Wacker just in-front of the beaver section of tray
• R/H/S behind headboard is 500mm for signs to be stored then a heavy-duty frame for customer supplied compressor to sit on 740mm long x 1400mm deep x 400mm high with fold down door fitted to outside edge
• R/H/S after compressor to be 100mm x 100mm RHS post uprights fitted to store tools into. This is to be raised above deck for cleaning purposes. 5 off post uprights
• 2 x Pipe reals fitted behind 1 off supplied and 1 of to be copied
• Recessed steps fitted behind reels just before beaver to access tray floor. Hand rail and hinged door fitted
• 1 x Mesh chock box fitted to each side of body under tray 1000mm long x 450mm deep x 500mm high Approximately, top 250mm is to be open for putting things into. 50 x 50 mesh cages painted black
• 2 x 1600mm long tubes fitted under rear of chassis where possible with rear end capped off and flat type cap with latch fitted to be able to lock. Accessible from L/H/S
• Fold down boot cleaner fitted on L/H/S under cabinet (brush type)
• 240volt inverter fitted in L/H/S front cabinet to run power lead off
• Slimline flashing beacon fitted to centre of headboard with switch fitted to dash with warning light
• Ladder holders fitted on inside edge of cabinets as per customer requirements
• 2 x swivel type work light fitted at headboard where possible wired to switch on dash with warning light